Biostar

According to A520 chipset specification, it doesn’t compatible with Ryzen 2000 series processors.

Please refer to the AMD Socket AM4 Chipset link below.

https://www.amd.com/en/products/processors/chipsets/am4.html

1. Open Realtek HD Audio Manager.

The icon is in the notification area (the lower right of the screen).

 
2. When using AC’97 front panel audio, audio manager will always show there are devices connected to the front panel.

 
3. Click the yellow icon on the upper right of the window. Check the box to Disable front panel jack detection. Then click OK.

Please follow the steps below :
1. Unplug the Power Cord from Power Supply and waiting for 2 minutes.
2. Install the M.2 Wi-Fi card into Wi-Fi slot.
3. Plug the Power Cord to Power Supply.
4. Install the M.2 Wi-Fi drivers (Wireless and Bluetooth).
5. Restart your system.
6. After system boot to Windows OS,try to check device manager, confrim the Wireless & Bluetooth device can be recognized.

If the M.2 SSD device is not detected, please try following methods for troubleshooting.

1. Ensure your M.2 device is working properly on other computers.

2. Reinstall M.2 device. Make sure it is installed properly.

3. Try another M.2 socket, if your motherboard has more than one M.2 sockets.

4. Ensure the device is recognized in BIOS.

a. Press delete when the system boots up to enter BIOS.

b. Go to Advanced >NVMe Configuration

5. Try other M.2 devices from the storage support list.

​Please go to BIOSTAR website to find the storage support list based on your motherboard model.

6. If your M.2 device is in Legacy boot mode, please enable CSM support.

a. Press delete to enter BIOS.

b. Go to Advanced > CSM Configuration / Go to Boot menu

c. Enable CSM support.

d. Press F10 save & exit.
 

Clear CMOS to make sure if the computer can boot up, please follow the step below.

1. Remove AC power line.
2. Set the jumper to “Pin 1-2 short”, you can use a metal object like a screwdriver to touch the
two pins.
3. Wait for five seconds.
4. After clearing the CMOS values, be sure the jumper is “Pin 1-2 open”.
5. Power on the AC.
6. Load Optimal Defaults and save settings in CMOS

(Please refer  user manual by different model to clear CMOS )

if you still have problems, please contact us via E-support

Please refer to the following table to choose the proper CNVi WiFi module.

• If you want to use AX211 module, please choose Intel 600 /700 series motherboard.
•  Please find your Wi-Fi module specification in Intel Ark to check " System Interface Type".

Q:Why am I got the message as this build of Vanguard requires TPM version 2.0 and secure boot to be enabled in order to play under Windows 11 ?

A: This article will teach you how to solve this problem.

Playing Valorant will need to enable TPM 2.0 and secure boot under windows 11 OS, you have to check that your motherboard is support TPM 2.0 system.

(NOTE: If your system unable to support TPM2.0, the only way that you can play Valorant is change your windows to older version as windows 10.)

Turn on TPM2.0 & Secure boot:

1.Press “delete” when you boot up, and go into BIOS.

2.Press “F3” to load optimized default settings and press “F10” save it.

3.Go security menu and choose secure boot and set as “enable”.

4.Choose key management(below secure boot) => restore factory keys => press "yes" => reset without saving to "no".

5.Advanced menu =>CSM configuration => CSM support set as "disabled".

6.After that press “F10” to save all the settings reboot to go into OS , and press “windows key” + R and type “tpm.msc”.

You will see the picture down below, if it show specification version is 2.0, you can totally play Valorant under this settings.

1. 請先在映泰 BIOSTAR 的官網上搜尋您的機種 , 並在該機種的 ”下載 ” 頁面選擇日期最新的BIOS版本 .

2. 點選下載鍵後 , 頁面上方將會跳出詢問檔案的下載方式 , 左邊為 BIOS檔案 , 右邊為BIOS壓縮檔案 , 建議直接選擇左邊的 BIOS 檔案進行下載 .

3. 下載 完成後將 BIOS檔案拉至USB隨身碟中 . 請在空白處點選右鍵 , “內容 ”並確認 USB 隨身碟的格式為 ”FAT32 ”.

4. 將 USB 隨身碟連接至要更新的系統上 .

5. 請將電腦開機 , 看到畫面後立即按下 ”Delete”鍵進到BIOS底下,此時畫面將 顯示如下

6. 進到BIOS底下後 , 請再按下F12進入更新BIOS的頁面 ”BIOS-FLASHER Utility” . 此時下圖的 ”fs0 ”為偵測到的 USB 裝置 , 若連接多個 USB 隨身碟 或硬碟, 則會出現數個可選擇裝置 ”fs1”, “fs2 ”以此類推 , 請確認正確隨身碟,並按下 ”Enter ” 將其開啟 .

7. 此時將會出現剛拉至 USB 隨身碟中的BIOS檔

8. 再次按下 ”Enter”,系統將會詢問是否更新此 BIOS 檔案 ,請按下”Y”鍵.

9.BIOS更新中 , 請勿關掉電源或執行其他動作.

10. 更新完成後 , 此時畫面如下 , 請按下 ”Y”進行重啟 . 重新啟動後 , 請再次按下 ”Delete” 鍵進到BIOS底下 .

11. 確認BIOS版本更新成功後,在進到 Windows之前 , 必須進行系統優化設定 請按下 ”F3 ”, 選擇 ”Yes”來進行優化設定 .

12. 再按 ”F10”, 一樣選擇 ”Yes ”後, 系統將會儲存並離開 .

13. 此時更新已經完成 , 可正常進行使用 .

Notice
1. Intel® Optane™ Memory H10 ( Here use Intel Optane Memory 32GB/512GB)
2. Install Intel Optane Memory H10, this technology only use in M.2 slots which are supported by chipset.
 

< BIOS/OS/Hardware installation setup >
1. Go to BIOS>Advanced Menu
1) Choose SATA configuration then set RAID in SATA mode.
2) Enable Hybrid Storage Detection and Configuration Mode.

(Make sure CSM Support is Disable.) Press F10 or select Save & Exit. (Legacy mode  is not supported.)
2. Please download the driver from the Intel official website. Unzip the file and move to the USB flash drive.
http://shorturl.at/pDIMT

3. Star install OS Windows 10 after above settings are ready. Please install OS under UEFI mode. (Legacy mode is not supported.)
 
4. 1) If you see the driver cannot found while installing Windows, please click Load Drive.

2) Select the driver(f6vmdflpy-x64 folder) in the USB flash drive.

3) Choose "Intel RST VMD Controller" then click Next.

4) Choose Unallocated Space and install Windows.
 

5. After finish the Windows OS Installation, please install "Intel Rapid Storage Technology driver and utility”. ( SetupRST.exe downloaded in step 2)
The system will reboot after finish the installation.
6. Then Install Intel® Optane™ Memory and Storage Management tool from Microsoft Store. Star the software after reboot.
 
7. You will see the status is Disable. Please select the drive.
1) Enable Intel Optane Memory.
 
2) Check "Erase all data on Intel Optane memory module and click Enable.
Then restart the system.
  

8.  Intel Optane Memory status will show Enable after reboot the system.
 

 

Warning

1. Do not remove the Optane™ memories to avoid the system damage.
2. If you want to replace/remove the Optane™ memories, please disable "Intel® Optane™ Memory and Storage Management" of the original memory first.

How to make RAID 0 with M.2 PCI-E hard disk on Intel 600 motherboard?

 1. Please press “Delete” when the system POST, to enter BIOS.

2. Press “F7” to go to advance model.

 3. Go to Advance-> SATA Configuration.

4. Set SATA Mode Selection to “RAID”

 5. Press “F10” to Save & Exit

 6. When the system boot on, go under BIOS-> Advanced ->Intel(R) Rapid Storage Technology.

7. Go to Create RAID Volume.

8. Set the RAID Level to “RAID0 (Stripe)” and change both of the Disk options to “X”.

 9. Select Create Volume.

 10. Then, enter the RAID Volume to check the details of RAID 0.

   11. After checking, press “F10” again to Save & Exit.

 12. When the system reboot automatically, press “F9” to select the bootable device and start the installation of OS.

How to install the RAID controller driver during Windows OS installation?

1. Boot the computer via Windows installation disc. And follow the instruction on the screen to star installing the windows.

2. Choose a type of installation, click Custom: Install Windows only (advanced). 

3. Choose Load Driver, then click Browse. 

You can go to the download page of  your product on BIOSTAR website. Download the driver below Intel Rapid Storage Technology(RAID Mode) and save it to your USB flash drive. 

4. Select VMD folder in your USB flash drive and click Next to finish the installation.